Important Plumber Guide for Installing a Bathtub
Important Plumber Guide for Installing a Bathtub
Blog Article
Have you been trying to find critical information on Tools You Need to Install a New Bathtub ?
Installing a tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a moderately challenging task. If the old bathtub is readily available, the job can move immediately; if you have to open up a wall to remove the old tub as well as place the new bathtub, the job is a lot harder. In either situation, the task is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and embeded in the brand-new one. Make certain you have certified yourself for the work as well as fit attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is far better to consider employing one before you begin. Opportunities are you might need a specialist plumber to make tube links.
This article will certainly aid you set up a brand-new bathtub in your shower room if you have actually already gotten a new tub as well as do not need to change the arrangement of your previous water pipelines.
Your devices and also material checklist need to consist of the following:
Preparing for the Installment
Firstly, the supporting structure supplied with the bathroom needs to be fitted (if needed) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop strain on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps making use of 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you should do is detach the water system. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The procedure of removing the existing taps can be quite problematic because of the restricted access that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will come from the pipelines. Once the supply pipes have actually been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from turning throughout this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any old securing substance.
Before moving on to fit the new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, place the tub in the required position. The wooden boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 small points.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub till the spirit level reviews level.
To mount faucets, fit all-time low of the outermost versatile faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water system and also check all joints and also brand-new pipework for leaks and tighten them if needed. Load the bathtub and also examine the overflow electrical outlet as well as the typical electrical outlet for leaks.
Finally, repair the bath paneling as explained in the producer's user's manual. Tiling and also sealing around the bathtub must wait up until the bath tub has been utilized at least when as this will certainly resolve it into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washers remain in location in between the tap as well as the sink. Safeguard the tap in place with the manufacturer given backnut. As soon as the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap ports. The former type should be connected to the tap ends initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about complications with dampness and also possible leaks to the ceiling listed below.
You can select from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes and cartridges, as well as are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the bathtub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealer can fracture relatively early if you do not consider this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly readily available on the marketplace. It is recommended to fit the tiles utilizing waterproof or waterproof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that report on Tools You Need to Install a New Bathtub through someone on our other website. Please take a moment to promote this article if you enjoyed reading it. Bless you for your time. Visit us again soon.
Click Here! Report this page